Swirlrepair kit 5 Cyl. Alfa Romeo 156 SW, 159 SW, 166, Brera, Spider 2.4 JTDM

Swirlrepair kit 5 Cyl. Alfa Romeo 156 SW, 159 SW, 166, Brera, Spider 2.4 JTDM
For a larger view click on the thumbnail
Swirlrepair kit 5 Cyl. Alfa Romeo 156 SW, 159 SW, 166, Brera, Spider 2.4 JTDM
Our previous price 74,90 EUR Now only 69,90 EURyou save 7% / 5,00 EUR
69,90 EUR per set
19 % VAT incl. excl. Shipping costs
Add to cart
Shipping time: in 2 weeks
Product no.: SR1100151
Manufacturer: Alfa Romeo - Originalteil


Products description


for the following Models:

Alfa Romeo 156 (932)
Alfa Romeo 156 SW (932)
Alfa Romeo GT Coupe (937)
Alfa Romeo 159 (939)
Alfa Romeo 159 SW (939)
Alfa Romeo Brera SW (939)
Alfa Romeo Spider SW (939)
Alfa Romeo 166 SW (939)

We only sell quality products from Alfa Romeo, brand manufacturers, or OEMs!

Important! Please give full car details when ordering!

What is SwirlRepair?

SwirlRepair is a repair kit for the swirl operating rod at the intake manifold:

Rather than replacing the intake manifold assembly including swirl flaps when just the operating rod is
damaged, Swirlrepair is a replacement for the worn plastic ball joint bushings of the operating
rod.

What are the advantages of SwirlRepair?

SwirlRepair is much cheaper than an exchange of the complete intake manifold assembly.
Also if the swirl operating rod has come adrift and your vehicle should not yet have recognized the
defect, a repair with SwirlRepair will still pay off quickly. Smoke is reduced for the benefit of the
engine and the environment, and also the performance increases while the fuel consumption
drops back to its usual, low level, so the expense on SwirlRepair can be returned after just a
few weeks.

Even if you should consider replacing the intake manifold assembly due to worn swirl flaps,
SwirlRepair helps as a temporary fix. It gives you time to find an affordable garage and/or
cheap parts while you can still use your car.

How does SwirlRepair work?

SwirlRepair consists of bushings made from high quality brass and stainless steel. You remove the
worn plastic ball joint bushings from the operating rod and attach the SwirlRepair bushings
with a 5.5mm key. In Addition it is sometimes necessary to drill a countersink in one of the
existing holes of the operating rod and use an extra bushing with a countersunk bolt, which is
supplied with the SwirlRepair kit. For the 20V five cylinder engine you simply use all five
bushings that are supplied. After this you just need to re-attach the operating rod to the ball
joints of the swirl flaps.

Inside the bushing you can see an o-ring, which is located in a groove. The o-ring is made from
temperature resistant material and works as a snap feature, thus keeping the bushing in place
on the swirl flap's ball joint. At the top the bushing a threaded stainless steel pin is installed,
which is used to attach the bushing to the operating rod with a stainless steel nut and spring
washer.

How is SwirlRepair installed?

Mounting SwirlRepair is easy. It just requires a bit of patience to attach the repaired operating rod as
the swirl flaps are not so easy to access, but this would be the same if you would try to
re-install the operating rod without fitting SwirlRepair.
If you prefer, you can also have SwirlRepair installed by a specialist, who should not need more than
15-20 minutes for the complete job even without any routine.
Furthermore we now also offer a complete and assembled rod, so you can simply exchange the
damaged rod with a new one.

Customers who bought this product also bought the following products:

Surge protection device, generator - 95980306
Suppresses permanently all dangerous voltage peaks
in the on-board network and thus protects the entire on-board electronics.

- 12 Volt
- Protection of the control units (ECU)
- Prevents premature bulb failure
- No polarity reversal possible
- Protection during jump starting and charging the battery

For permanent battery connection. Non-polarizable, simply clamp between the battery terminals (+/-)
Bulbs are damaged by sustained overvoltages and vibrations.
Failure despite voltage spike killer may be due to lamp pre-damage,
vibration or a faulty alternator regulator.

your price 11,90 EURMSRP 16,28 EUR
11,90 EUR per pieces
19 % VAT incl. excl. Shipping costs
Coupling rod set reinforced FA (HD) Alfa 159, Brera, Spider

coupling rod set, (HD) reinforced version:
for the following Models at the front axle right and left side

Alfa 159 (939)
Alfa 159 & SW (939)
Alfa Brera (939)
Alfa New Spider (939)

Product Features:
- Increased bullet diameter Ø 22,0 mm
- Reinforced connecting rod Ø 10.0 mm
- High quality blue plastic seats
- High-quality high-fat
- 16mm wrench attachment

Advantage:
- Significantly longer runtime by reinforced design!
You find more information under article details, and/or on the picture click!
your price 70,00 EURMSRP 94,56 EUR
35,00 EUR per pieces
19 % VAT incl. excl. Shipping costs

This Product was added to our catalogue on 29/11/2017.